ⓘ Clock rate. The clock rate typically refers to the frequency at which the clock generator of a processor can generate pulses, which are used to synchronize the ..


ⓘ Clock rate

The clock rate typically refers to the frequency at which the clock generator of a processor can generate pulses, which are used to synchronize the operations of its components, and is used as an indicator of the processors speed. It is measured in clock cycles per second or its equivalent, the SI unit hertz. The clock rate of the first generation of computers was measured in hertz or kilohertz, the first personal computers to arrive throughout the 1970s and 1980s had clock rates measured in megahertz, and in the 21st century the speed of modern CPUs is commonly advertised in gigahertz. This metric is most useful when comparing processors within the same family, holding constant other features that may affect performance. Video card and CPU manufacturers commonly select their highest performing units from a manufacturing batch and set their maximum clock rate higher, fetching a higher price.


1.1. Determining factors Binning

Manufacturers of modern processors typically charge premium prices for processors that operate at higher clock rates, a practice called binning. For a given CPU, the clock rates are determined at the end of the manufacturing process through actual testing of each processor. Chip manufacturers publish a "maximum clock rate" specification, and they test chips before selling them to make sure they meet that specification, even when executing the most complicated instructions with the data patterns that take the longest to settle testing at the temperature and voltage that runs the lowest performance. Processors successfully tested for compliance with a given set of standards may be labeled with a higher clock rate, e.g., 3.50 GHz, while those that fail the standards of the higher clock rate yet pass the standards of a lesser clock rate may be labeled with the lesser clock rate, e.g., 3.3 GHz, and sold at a lower price.


1.2. Determining factors Engineering

The clock rate of a CPU is normally determined by the frequency of an oscillator crystal. Typically a crystal oscillator produces a fixed sine wave - the frequency reference signal. Electronic circuitry translates that into a square wave at the same frequency for digital electronics applications. The clock distribution network inside the CPU carries that clock signal to all the parts that need it. An A/D Converter has a "clock" pin driven by a similar system to set the sampling rate. With any particular CPU, replacing the crystal with another crystal that oscillates at half the frequency "underclocking" will generally make the CPU run at half the performance and reduce waste heat produced by the CPU. Conversely, some people try to increase performance of a CPU by replacing the oscillator crystal with a higher frequency crystal "overclocking". However, the amount of overclocking is limited by the time for the CPU to settle after each pulse, and by the extra heat created.

After each clock pulse, the signal lines inside the CPU need time to settle to their new state. That is, every signal line must finish transitioning from 0 to 1, or from 1 to 0. If the next clock pulse comes before that, the results will be incorrect. In the process of transitioning, some energy is wasted as heat mostly inside the driving transistors. When executing complicated instructions that cause many transitions, the higher the clock rate the more heat produced. Transistors may be damaged by excessive heat.

There is also a lower limit of the clock rate, unless a fully static core is used.


2. Historical milestones and current records

The first electromechanical general purpose computer, the Z3, operated at a frequency of about 5–10 Hz. The first electronic general purpose computer, the ENIAC, used a 100 kHz clock in its cycling unit. As each instruction took 20 cycles, it had an instruction rate of 5 kHz.

The first commercial PC, the Altair 8800 by MITS, used an Intel 8080 CPU with a clock rate of 2 MHz 2 million cycles per second. The original IBM PC c. 1981 had a clock rate of 4.77 MHz 4.772.727 cycles per second. In 1992, both Hewlett-Packard and Digital Equipment Corporation broke the difficult 100 MHz limit with RISC techniques in the PA-7100 and AXP 21064 DEC Alpha respectively. In 1995, Intels P5 Pentium chip ran at 100 MHz 100 million cycles per second. On March 6, 2000, AMD reached the 1 GHz milestone a few months ahead of Intel. In 2002, an Intel Pentium 4 model was introduced as the first CPU with a clock rate of 3 GHz three billion cycles per second corresponding to ~3.3×−10 seconds or 0.33 nanoseconds per cycle. Since then, the clock rate of production processors has increased much more slowly, with performance improvements coming from other design changes.

As of 2014, the Guinness World Record for the highest CPU clock rate is an overclocked, 8.723 GHz AMD Piledriver-based FX-8370 chip. It surpassed the previous record achieved in 2011, an 8.429 GHz AMD FX-8150 Bulldozer-based chip.

As of mid-2013, the highest clock rate on a production processor is the IBM zEC12, clocked at 5.5 GHz, which was released in August 2012.


3. Research

Engineers continue to find new ways to design CPUs that settle a little more quickly or use slightly less energy per transition, pushing back those limits, producing new CPUs that can run at slightly higher clock rates. The ultimate limits to energy per transition are explored in reversible computing.

The first fully reversible CPU, the Pendulum, was implemented using standard CMOS transistors in the late 1990s at MIT.

Engineers also continue to find new ways to design CPUs so that they complete more instructions per clock cycle, thus achieving a lower CPI cycles or clock cycles per instruction count, although they may run at the same or a lower clock rate as older CPUs. This is achieved through architectural techniques such as instruction pipelining and out-of-order execution which attempts to exploit instruction level parallelism in the code.

IBM is working on 100 GHz CPU. In 2010, IBM demonstrated a graphene based transistor that can execute 100 billion cycles per second.


4. Comparing

The clock rate of a CPU is most useful for providing comparisons between CPUs in the same family. The clock rate is only one of several factors that can influence performance when comparing processors in different families. For example, an IBM PC with an Intel 80486 CPU running at 50 MHz will be about twice as fast internally only as one with the same CPU and memory running at 25 MHz, while the same will not be true for MIPS R4000 running at the same clock rate as the two are different processors that implement different architectures and microarchitectures. Further, a "cumulative clock rate" measure is sometimes assumed by taking the total cores and multiplying by the total clock rate e.g. dual core 2.8 GHz being considered processor cumulative 5.6 GHz. There are many other factors to consider when comparing the performance of CPUs, like the width of the CPUs data bus, the latency of the memory, and the cache architecture.

The clock rate alone is generally considered to be an inaccurate measure of performance when comparing different CPUs families. Software benchmarks are more useful. Clock rates can sometimes be misleading since the amount of work different CPUs can do in one cycle varies. For example, superscalar processors can execute more than one instruction per cycle on average, yet it is not uncommon for them to do "less" in a clock cycle. In addition, subscalar CPUs or use of parallelism can also affect the performance of the computer regardless of clock rate.

  • using the clock signal for synchronization may become active at either the rising edge, falling edge, or, in the case of double data rate both in the
  • accurately, real clocks will differ after some amount of time due to clock drift, caused by clocks counting time at slightly different rates There are several
  • The molecular clock is figurative term for a technique that uses the mutation rate of biomolecules to deduce the time in prehistory when two or more life
  • Quad data rate QDR, or quad pumping is a communication signaling technique wherein data are transmitted at four points in the clock cycle: on the rising
  • A clock is an instrument used to measure, keep, and indicate time. The clock is one of the oldest human inventions, meeting the need to measure intervals
  • seed dispersal Clock signal, a signal used in a synchronous circuit Clock rate the frequency of a central processing unit CPU Clock software a bundled
  • and resists swinging at other rates From its invention in 1656 by Christiaan Huygens until the 1930s, the pendulum clock was the world s most precise
  • simple water clocks which were of the outflow type, were stone vessels with sloping sides that allowed water to drip at a nearly constant rate from a small
  • A real - time clock RTC is a computer clock most often in the form of an integrated circuit that keeps track of the current time. Although the term
  • A turret clock or public clock is a clock designed to be mounted high in the wall of a building, usually in a clock tower, in public buildings such as
  • reaction being studied. Radical clock reactions involve a competition between a unimolecular radical reaction with a known rate constant and a bimolecular
  • in the clock s rate caused by the varying force of the spring as it unwound. It was used in precision pendulum clocks and in automotive clocks until the